Hitachi IC35L060AVV207 Datasheet Page 101
- Page / 247
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
4. Advanced usage using protected area
The data in the protected area is accessed by the following method:
i. Issue Read Native Max Address command to get the real device maximum LBA. Returned value
shows that native device maximum LBA is 12,692,735 (C1ACFFh) regardless of the current
setting.
ii. Make the entire device including the protected area accessible by setting device maximum LBA
as 12,692,735 (C1ACFFh) via the Set Max Address command with the volatile option. By using
this option an unexpected power removal or reset will not keep the protected area accessible.
iii. Read information data from protected area.
iv. Issue hard reset or POR to inhibit any access to the protected area.
9.8.2 Security extensions
1. Set Max Set Password
2. Set Max Lock
3. Set Max Freeze Lock
4. Set Max Unlock
The Set Max Set Password command allows the host to define the password to be used during the cur-
rent power on cycle. The password does not persist over a power cycle but does persist over a hardware
or software reset. This password is not related to the password used for the Security Mode Feature set.
When the password is set the device is in the Set_Max_Unlocked mode. The Set Max Lock command
allows the host to disable the Set Max commands (except set Max Unlock) until the next power cycle or
the issuance and acceptance of the Set Max Unlock command. When this command is accepted, the
device is in the Set_Max_Locked mode. The Set Max Unlock command changes the device from the
Set_Max_Locked mode to the Set_Max_Unlocked mode. The Set Max Freeze Lock command allows the
host to disable the Set Max commands (including Set Max UNLOCK) until the next power cycle. When
this command is accepted, the device is in the Set_Max_Frozen mode.
The IDENTIFY DEVICE response word 83, bit 8 indicates that this extension is supported if set, and word
86, bit 8 indicates the Set Max security extension is enabled if set.
Deskstar 180GXP hard disk drive specifications
87
- Deskstar 180 GXP 1
- Table of contents 5
- List of figures 11
- 1.0 General 15
- 2.0 General features 17
- 3.1 Control Electronics 21
- 3.2 Head disk assembly 21
- 3.3 Actuator 21
- 4.0 Drive characteristics 23
- 4.2 Data sheet 24
- 4.3 Drive organization 25
- 4.4.1 Command overhead 26
- 4.4.2 Mechanical positioning 26
- Figure 7. Head switch time 27
- 4.4.3 Drive ready time 28
- 4.4.4 Data transfer speed 29
- 4.4.5 Throughput 30
- 4.4.6 Operating modes 30
- Operating mode descriptions 30
- 5.0 Defect flagging strategy 33
- 6.0 Specification 35
- 6.1.2 Signal definition 36
- 6.2 Signal timings 40
- 6.2.2 PIO timings 41
- 6.2.3 Multiword DMA timings 43
- 6.2.4 Ultra DMA timings 44
- HDMARDY– is negated 45
- 6.2.4.5 Initiating Write DMA 48
- DDMARDY– is negated 49
- 6.2.5 Addressing of registers 52
- 6.2.6 Cabling 52
- 6.3 Jumper settings 53
- 6.3.4.4 Power Up In Standby 58
- 6.4 Environment 59
- Nonoperating 60
- Operating 60
- 6.5 DC power requirements 61
- 6.6 Reliability 64
- 6.7 Mechanical specifications 65
- BREATHER HOLE 66
- 6.7.2 Hole locations 67
- 6.7.3Connector locations 68
- 6.7.4 Drive mounting 68
- 6.8 Vibration and shock 69
- 6.8.3 Operating shock 70
- 6.8.4 Nonoperating shock 70
- 6.9 Acoustics 71
- 6.10 Identification labels 72
- 6.11 Safety 73
- 6.12.1 CE Mark 74
- 6.12.2 C-Tick Mark 74
- 7.0 General 77
- Deviations from standard 77
- 8.0 Registers 79
- 8.2 Command Register 80
- 8.3 Cylinder High Register 80
- 8.4 Cylinder Low Register 80
- 8.5 Data Register 81
- 8.6 Device Control Register 81
- 8.7 Drive Address Register 81
- 8.8 Device/Head Register 82
- 8.9 Error Register 82
- 8.10 Features Register 83
- 8.11 Sector Count Register 83
- 8.12 Sector Number Register 83
- 8.13 Status Register 84
- 9.0 General operation 85
- 9.1.1 Register initialization 86
- 9.3 Sector Addressing Mode 88
- 9.5 Power management feature 90
- Figure 79. Power conditions 91
- 9.6 S.M.A.R.T. function 92
- 9.6.8 Self-test 93
- 9.7 Security Mode Feature Set 94
- 9.7.4 Operation example 95
- Figure 81. Usual Operation 96
- 9.7.4.4 User Password Lost 97
- 9.7.5 Command table 98
- 9.8.2 Security extensions 101
- 9.9 Seek Overlap 102
- 9.10 Write cache function 103
- 9.11 Reassign function 103
- 9.15 Address Offset Feature 105
- 9.15.2 Identify Device Data 106
- 10.0 Command Protocol 109
- 10.1 PIO Data In commands 110
- 10.2 PIO Data Out commands 112
- 10.3 Non-data commands 114
- 10.4 DMA commands 116
- 10.5 DMA queued commands 117
- 11.0 Command descriptions 119
- (subcommand C1h) 125
- 11.4 Flush Cache (E7h) 129
- 11.5 Flush Cache Ext (EAh) 130
- 11.6 Format Track (50h) 131
- 11.7 Format Unit (F7h) 133
- 11.8 Identify Device (ECh) 134
- 11.9 Idle (E3h/97h) 141
- 11.12 NOP (00h) 144
- 11.13 Read Buffer (E4h) 145
- 11.14 Read DMA (C8h/C9h) 146
- 11.15 Read DMA Ext (25h) 148
- Read DMA Ext Command (25h) 148
- 11.16 Read DMA Queued (C7h) 150
- 11.18 Read Log Ext (2Fh) 154
- BytesDescription 155
- 11.18.2.1 Error log version 156
- 11.18.2.2 Error log index 156
- 11.18.2.4 Device error count 158
- 11.19 Read Long (22h/23h) 161
- 11.20 Read Multiple (C4h) 163
- 11.21 Read Multiple Ext (29h) 165
- 11.28 Recalibrate (1xh) 177
- 11.34 Security Unlock (F2h) 185
- 11.35 Seek (7xh) 187
- 11.36 Service (A2h) 188
- 11.37 Set Features (EFh) 189
- 11.37.1 Set Transfer mode 190
- 11.37.2 Write Cache 190
- Software Resets 192
- 11.38 Set Max Address (F9h) 193
- Figure 151. Set Max Lock 196
- 11.40 Set Multiple (C6h) 201
- 11.41 Sleep (E6h/99h) 202
- 11.42.1 S.M.A.R.T. Subcommand 204
- ByteDescription 208
- 11.42.4 SMART Log Directory 213
- 11.42.5.2 Error log index 214
- 11.42.5.3 Device error count 214
- 11.42.7 Error reporting 218
- 11.43 Standby (E2h/96h) 219
- 11.45 Write Buffer (E8h) 222
- 11.46 Write DMA (CAh/CBh) 223
- 11.47 Write DMA Ext (35h) 225
- 11.50 Write Log Ext (3Fh) 231
- 11.51 Write Long (32h/33h) 233
- 11.52 Write Multiple (C5h) 235
- 12.0 Timings 243
- Addressing of registers, 38 245
- Technologies 247
- DeskstarTM is a trademark of 247
Related products and manuals for Internal hard drives Hitachi IC35L060AVV207
(2 pages)© 2020, manymanuals.com. All rights reserved. | 0.085 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals