Hitachi L100 User Manual Page 96
- Page / 163
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
L100 Inverter
Operations
and Monitoring
4–5
Specifications of Control and Logic Connections
The control logic connectors are located just behind the front panel half-door. The relay
contacts are accessible behind the main door. Connector labeling is shown below.
Specifications for the logic connection terminals are in the following table:
Note 1:
The two terminals “L” are electrically connected together inside the inverter.
P24
123L 45
1112
CM2FM
O LOIH
AL0 AL1 AL2
Relay
contacts
Logic
inputs
Analog
Inputs
Analog
Output
Logic
outputs
Terminal Name Description Ratings
P24 +24V for logic inputs 24VDC, 30 mA max (do not short to terminal L)
1, 2, 3, 4, 5 Discrete logic inputs 27VDC max. (use P24 or an external supply refer-
enced to terminal L)
L (top row) *1 GND for logic inputs sum of input 1-6 currents (return)
11, 12 Discrete logic outputs 50mA maximum ON state current,
27 VDC maximum OFF state voltage
CM2 GND for logic outputs 100 mA: sum of 11 and 12 currents (return)
FM PWM (analog/digital) output 0 to 10VDC, 1 mA, PWM and 50% duty digital
L (bottom row) *1 GND for analog inputs sum of OI, O, and H currents (return)
OI Analog input, current 4 to 19.6 mA range, 20 mA nominal
O Analog input, voltage 0 to 9.6 VDC range, 10VDC nominal,
input impedance 10 k
Ω
H +10V analog reference 10VDC nominal, 10 mA max
AL0 Relay common contact 250 VAC, 2.5A (R load) max.,
250 VAC, 0.2A (I load, P.F=0.4) max.
100 VAC, 10mA min.
30 VDC, 3.0A (R load) max.
30 VDC, 0.7A (I load, P.F.=0.4) max.
5 VDC, 100mA min.
AL1 Relay contact, normally
closed during RUN
AL2 Relay contact, normally open
during RUN
Technologies Inc.
Toll Free: voice: 1-877-539-2542 fax: 1-800-539-2542 www.mgitech.com
- L100 Series Inverter 1
- Instruction Manual 1
- Table of Contents 2
- Safety Messages 4
- Hazardous High Voltage 4
- Powerup Test Caution Messages 10
- Technologies Inc 11
- General Warnings and Cautions 13
- General Caution 15
- Revisions 16
- Getting Started 18
- Inverter Specifications Label 20
- Model Number Convention 20
- L100 Inverter Specifications 21
- General Specifications 23
- What is an Inverter? 24
- Inverter Output to the Motor 26
- Velocity Profiles 28
- Frequently Asked Questions 29
- Inverter Mounting 32
- Unpacking and Inspection 33
- Main Physical Features 33
- Name Function 36
- Choosing a Mounting Location 37
- L100 Inverter 40
- Preparation for Wiring 43
- Powerup Test 48
- Potentiometer Enable LED 50
- Hertz / Amperes LEDs 50
- Monitor Mode 52
- Program Mode 52
- STOPSTOP 56
- Configuring 57
- Drive Parameters 57
- Choosing a Programming Device 58
- Using Keypad Devices 59
- RS232/422 62
- 2-meter cable, RJ45 62
- Programming with the DOP Plus 63
- “A” Group: Standard Functions 66
- Analog Input Settings 67
- Multi-speed Frequency Setting 68
- V/F Characteristics 69
- DC Braking Settings 71
- Frequency-related Functions 72
- PID Control 73
- Restart Mode 77
- Overload Restriction 79
- Software Lock Mode 80
- Miscellaneous Settings 81
- Input Terminal Configuration 83
- Output Terminal Configuration 87
- Multi-Speed Select 98
- (LSB)(MSB) 99
- Operations 100
- Jogging Command 100
- Free-run Stop 102
- External Trip 103
- Unattended Start Protection 104
- Software Lock 105
- Reset Inverter 107
- Run Signal 109
- Frequency Arrival Signal 110
- Analog Input Operation 115
- See I/O specs on page 4–5 117
- Output value 117
- PID Loop Operation 118
- Simultaneous Connections 119
- Motor Control 120
- Accessories 120
- Introduction 121
- Component Descriptions 122
- Dynamic Braking 124
- Troubleshooting 126
- Troubleshooting Tips 128
- Monitor Menu 130
- Trip History 130
- Current Trip 130
- Conditions 130
- Error Codes 131
- Maintenance and Inspection 134
- Spare parts 135
- Capacitor Life Curve 135
- INVERTER 137
- Warranty 139
- Glossary and 140
- Bibliography 140
- Glossary 141
- Drive Parameter 148
- Settings Tables 148
- Appendix B 150
- Standard Functions 150
- Fine Tuning Functions 152
- Monitor Mode Parameters 154
- Function Mode Setup 155
Related products and manuals for Tools Hitachi L100
Tools Hitachi DV 18DL User Manual
(86 pages)
(86 pages)
Tools Hitachi SJ2-CO User Manual
(35 pages)
(35 pages)
Tools Hitachi DV 10DVA User Manual
(38 pages)
(38 pages)
Tools Hitachi C6DD User Manual
(22 pages)
(22 pages)
Tools Hitachi N 5008AC User Manual
(42 pages)
(42 pages)
Tools Hitachi H 65 User Manual
(12 pages)
(12 pages)
Tools Hitachi DH 30PC User Manual
(76 pages)
(76 pages)
Tools Hitachi DH 24PD User Manual
(28 pages)
(28 pages)
Tools Hitachi DH 38YE User Manual
(64 pages)
(64 pages)
Tools Hitachi SJ300 User Manual
(76 pages)
(76 pages)
Tools Hitachi DV14DMR User Manual
(96 pages)
(96 pages)
Tools Hitachi CR 13VA User Manual
(60 pages)
(60 pages)
Tools Hitachi 24PD User Manual
(58 pages)
(58 pages)
Tools Hitachi WR 22SA User Manual
(21 pages)
(21 pages)
Tools Hitachi H 45MR User Manual
(52 pages)
(52 pages)
Tools Hitachi GM7000 231327 User Manual
(36 pages)
(36 pages)
Tools Hitachi CR 18DV User Manual
(80 pages)
(80 pages)
Tools Hitachi DH 40FB User Manual
(60 pages)
(60 pages)
Tools Hitachi DS 14DMR User Manual
(88 pages)
(88 pages)
© 2020, manymanuals.com. All rights reserved. | 0.060 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals