Hitachi C 8FB2 User Manual Page 23
- Page / 76
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
23
English
3. Inspecting the carbon brushes (Fig. 39 and Fig. 40)
The carbon brushes in the motor are expendable parts.
If the carbon brushes become excessively worn, motor trouble might occur.
Therefore, inspect the carbon brushes periodically and replace them when they have become worn to
the wear limit line as shown in Fig. 39.
Also, keep the carbon brushes clean so that they will slide smoothly within the brush holders.
The carbon brushes can easily be removed after removal of the brush caps (see Fig. 40) with a slotted
(minus) screwdriver.
Fig. 39 Fig. 40
4. Inspecting the mounting screws
Regularly inspect each component of the power tool for looseness.
Re-tighten mounting screws on any loose part.
WARNING: To prevent personal injury, never operate the power tool if any components are loose.
5. Inspecting the safety covers for proper operation
Before each use of the tool, test the safety covers (see Fig. 7) to assure that they are in good condition
and that they move smoothly.
Never use the tool unless the safety covers operate properly and it is in good mechanical condition.
6. Storage
After operation of the tool has been completed, check that the following has been performed:
(1) Trigger switch is in OFF position,
(2) Power plug has been removed from the receptacle,
(3) Lock-off button has been removed and stored in a secure place.
When the tool is not in use, keep it stored in a dry place out of the reach of children.
7. Handle (for transportation and carrying)
For transportation purpose, grasp the handle with one hand and
hold the base at the left end grip section with the other to carry.
NOTE: Before transporting or carrying, position saw blade
against guard and tighten slide securing knob to stop slide
motion.
Fig. 41
8. Lubrication
Lubricate the following sliding surfaces once a month to keep the power tool in good operating condition
for a long time (see Fig. 1 and Fig. 2). Use of machine oil is recommended.
Oil supply points:
*Rotary portion of hinge
*Rotary portion of vise assembly
*Sliding portion of slide pipe (A) and slide pipe (B)
Wear Limit Line
43
1/4" (6mm)
No. 43 indicates the last
two numbers of carbon
brush Code No.
Brush Cap
Groove for Driver
11/16" (17mm)
Base
Guard
Slide
Securing
Knob
Handle for
Transportation
Blade
- AVERTISSEMENT 1
- ADVERTENCIA 1
- CONTENTS 2
- TABLE DES MATIERES 2
- IMPORTANT INFORMATION 3
- MEANINGS OF SIGNAL WORDS 3
- REPLACEMENT PARTS 6
- USE PROPER EXTENSION CORD 6
- SAVE THESE INSTRUCTIONS 7
- MAKE THEM AVAILABLE TO 7
- OTHER USERS OF THIS TOOL! 7
- OPERATION AND MAINTENANCE 8
- SPECIFICATIONS 9
- ACCESSORIES 9
- APPLICATIONS 10
- PREPARATION BEFORE OPERATION 10
- BEFORE USING 11
- BEFORE CUTTING 12
- 4. Oblique angle 13
- 5. Securing the workpiece 13
- PRACTICAL APPLICATIONS 14
- 1. Switch operation 15
- 4. Cutting Operation 16
- 7. Bevel cutting procedures 18
- 8. Miter cutting procedures 18
- Fig. 27 Fig. 28 19
- 11. Groove cutting procedures 20
- Fig. 37-a Fig. 37-b 21
- MAINTENANCE AND INSPECTION 22
- Fig. 39 Fig. 40 23
- SERVICE AND REPAIRS 24
- SÉCURITÉ 25
- CONSERVER CES INSTRUCTIONS 29
- LES METTRE A LA DISPOSITION 29
- UTILISATION ET ENTRETIEN 30
- SPÉCIFICATIONS 31
- ACCESSOIRES 31
- AVANT L’UTILISATION 33
- AVANT LA COUPE 34
- 4. Angle oblique 35
- 5. Fixation de la pièce 35
- APPLICATIONS PRATIQUES 36
- 4. Coupe 38
- Fig. 29 Fig. 31 42
- Fig. 30 Fig. 32 42
- Fig. 33 Fig. 34 42
- ENTRETIEN ET INSPECTION 44
- 9. Nettoyage 46
- SEGURIDAD 47
- GUARDE ESTAS INSTRUCCIONES 51
- A MANO PARA QUE PUEDAN 51
- USARLAS OTROS QUE DESEEN 51
- UTILIZAR ESTA HERRAMIENTA 51
- OPERACIÓN Y MANTENIMIENTO 52
- ESPECIFICACIONES 53
- ACCESORIOS 53
- APLICACIONES 54
- ANTES DE LA UTILIZACIÓN 55
- ANTES DEL CORTE 56
- 4. Ángulo oblicuo 57
- APLICACIONES PRÁCTICAS 58
- 4. Operación de corte 60
- ADVERTENCIA: * 61
- MANTENIMIENTO E INSPECCIÓN 66
- SERVICIO Y REPARACIONES 68
- PARTS LIST 69
- Slide Compound Saw Parts List 71
- Standard Accessories 72
- Optional Accessories 72
- Hitachi Koki Co., Ltd 76
Related products and manuals for Power saws Hitachi C 8FB2
Power saws Hitachi C10RA2 User Manual
(85 pages)
(85 pages)
Power saws Hitachi C 10FCE User Manual
(76 pages)
(76 pages)
Power saws Hitachi CJ120V User Manual
(58 pages)
(58 pages)
Power saws Hitachi C 15FB User Manual
(54 pages)
(54 pages)
Power saws Hitachi CJ120VA User Manual
(60 pages)
(60 pages)
Power saws Hitachi CC14SE OM User Manual
(52 pages)
(52 pages)
Power saws Hitachi C 7BMR User Manual
(40 pages)
(40 pages)
Power saws Hitachi C 10FS User Manual
(84 pages)
(84 pages)
Power saws Hitachi FCJ 55 User Manual
(30 pages)
(30 pages)
Power saws Hitachi C 9SA2 User Manual
(18 pages)
(18 pages)
© 2020, manymanuals.com. All rights reserved. | 1.342 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals