Hitachi L40A105A User Manual download pdf (Page 13)

ENGLISH

Starting setup

The Auto Setup menu appears the first time you turn on the

TV, and assists you to specify the Air/Cable setting, and

program your channels automatically.

IMPORTANT: Make sure that the antenna or cable TV system

connection is made!

To turn on the TV, press POWER (POWER indicator on the

front of the unit changes green. It may take approx. 10 seconds

for a picture to appear on screen.). The Auto Setup function

begins.

Auto Setup

Scan Start

TV Location Store

E-POP Demo On

Source Cable

Press ▲ or ▼ to select “TV Location”, then press ◀ or ▶ to

select “Home” or “Store”. This product qualifies for ENERGY

STAR In Home mode default setting.

NOTE:

This unit has been preset to STORE brightness. This setting

does not qualify under ENERGY STAR. To reduce brightness

and energy consumption, change setting to ‘HOME’. This

setting does qualify under ENERGY STAR.

The device may not conform to the ENERGY STAR standard

after Reset is performed or the Backlight is adjusted.

•

Press ▲ or ▼ to select “E-POP Demo”, then press ◀ or ▶ to

select “On” or “Off”.

On: A TV feature introduction will be popped up at the bottom

of the screen.

Off: Turn off the E-POP Demo feature.

Press ▲ or ▼ to select “Source”, then press ◀ or ▶ to select

“Air” or “Cable”.

Press ▲ or ▼ to select “Scan”, then press ▶ or ENTER.

“Auto Setup” will begin. After the Auto Setup is completed, the

TV channel appears on the screen.

Depending on the reception condition, it may take up to 30

minutes to complete memorizing digital cable channels.

Please allow the process to complete without interruption.

•

NOTE:

If you press EXIT in the process of “Auto Setup”, the Auto Setup

stops and changes to the normal screen.

When you make a menu selection, your changes occur

immediately. You do not have to press EXIT to see your changes.

TV operation

To turn on the TV, press POWER.

(POWER indicator on the front of the unit changes green.

It may take approx. 10 seconds for a picture to appear on

screen.)

Adjust the volume level by pressing VOL + or – . The volume

level will be indicated on the screen by green bars. As the

volume level increases, so do the number of bars. If the

volume decreases, the number of green bars also decreases.

Set the Source option to the appropriate position (see “Air/

Cable selection” on page 16).

Press the Direct Channel Selection Buttons (0-9, –)

buttons to select the channel.

(If you press only the channel number, channel selection will

be delayed for a few seconds.)

•

TO SELECT ANALOG CHANNELS

1-9: Press 1-9 as needed. Example, to select channel 2,

press 2, then press ENTER.

10-99: Press the 2 digits in order. Example, to select

channel 12, press 1, 2, then press ENTER.

100-135: Press the 3 digits in order. Example, to select

channel 120, press 1, 2, 0, then press ENTER.

TO SELECT DIGITAL CHANNELS

Press the first 1-3 digits, then press the – button followed by

the remaining number.

Example, to select channel 15-1, press 1, 5, –, 1, then press

ENTER.

If a channel is selected with only audio content, “Audio only”

will be displayed on the screen.

If a channel is selected with a weak digital signal, “Weak

Signal or Channel not available.” will be displayed on the

screen.

The same program may be available on either an analog

channel or a digital channel. You may choose to watch

either format.

If a channel is selected to which you have not subscribed,

“Digital channel is encrypted” will be displayed on the

screen.

•

VHF/UHF/CABLE CHANNELS

Air Cable

VHF

2-13

VHF

2-13

UHF

14-69

STD/HRC/IRC

14-36 (A) (W)

37-59 (AA) (WW)

60-85 (AAA) (ZZZ)

86-94 (86) (94)

95-99 (A-5) (A-1)

100-135 (100) (135)

01 (4A)

NOTE:

If a channel with no broadcast is selected, the sound will

automatically be muted.

It may take a few seconds for a digital channel picture to appear

on screen after being selected.

To select the video input source

To view a signal from another device connected to your LCD

TV, such as a VCR player, press INPUT, then press ▲ or ▼ or

corresponding Number buttons (0-7), then press ENTER. You

can select TV, Video1, Video2, Component, HDMI1, HDMI2,

HDMI3 or PC depending on which input jacks you used to connect

your devices.

Input List

0.TV

1.Video1

3.Component

2.Video2

4.HDMI1

[0-7]:Select

5.HDMI2

6.HDMI3

7.PC

CH /

Press and release CH / . The channel automatically stops at

the next channel set into memory.

For proper operation, before selecting channels, they should be

set into the memory. See “Memorizing channels” on page 16.

•

3IM0821B_En.indd 133IM0821B_En.indd 13 11/29/11 10:06:02 AM11/29/11 10:06:02 AM

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 28 29

Comments to this Manuals

No comments

Hitachi L40A105A User Manual Page 13

Comments to this Manuals

Related products and manuals for LCD TVs Hitachi L40A105A