Hitachi CP-S220W User Manual Page 1

ENGLISHLiquid Crystal ProjectorCP-S220WUSER'S MANUAL1-1Thank you for purchasing this HITACHI liquid crystal projector.Please read the accompanyin

1-10OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))Table 1.2 Basic Operation (continued)Item DescriptionVOLUMEVolume adjustment : Reduce VOLUME ↔ Increas

1-11OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHSetup MenuThe following adjustments and settings arepossible when SETUP is selected at the top

1-12OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))Input MenuThe following functions are available when INPUT is selected on themenu. Select an item with

1-13OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHImage MenuThe following adjustments and settings are available when IMAGE isselected on the men

1-14OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))Options MenuThe following adjustments and settings are available when OPTIONS isselected on the menu.

1-15OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHNo Signal MenuThe same adjustments and settings are available as with the Image andOptions menu

* For disposal of used lamp, treat according to the instruction of community authorities.* Since the lamp is made of glass, do not apply shock to it a

1-17MMAAIINNTTEENNAANNCCEE ((ccoonnttiinnuueedd))ENGLISHReplacing the Lamp1. Switch the projector OFF, remove the power cord from the poweroutlet, an

1-18MMAAIINNTTEENNAANNCCEE ((ccoonnttiinnuueedd))Air Filter MaintenanceThe air filter should be cleaned as described below at intervals of approximat

1-19ENGLISHTROUBLESHOOTINGOSD MessageA message like the bottom table sometimes displays it with this opportunity at the time of powersource on.Cope in

1-2FEATURESThis liquid crystal projector is used to project various computer signals as well as NTSC / PAL /SECAM video signals onto a screen. Little

1-20TTRROOUUBBLLEESSHHOOOOTTIINNGG ((ccoonnttiinnuueedd))Indicators MessageThe POWER indicator, LAMP indicator and TEMP indicator light or blink in t

1-21ENGLISHTTRROOUUBBLLEESSHHOOOOTTIINNGG ((ccoonnttiinnuueedd))SymptomBefore requesting repair, check in accordance with the following chart. If the

1-22SPECIFCATIONSItem SpecificationProduct name Liquid crystal projectorModel CP-S220WLiquidcrystalpanelPanel size 1.8 cm (0.7 type)Drive system TFT a

1-23ENGLISHSSPPEECCIIFFCCAATTIIOONNSS ((ccoonnttiinnuueedd))Dimension Diagram2897645.674.5210WARRANTY AND AFTER-SERVICE* When a problem occurs, pleas

1-24REGULATORY NOTICESWARNING: This equipment has been tested and found to comply with thelimits for a Class B digital device, pursuant to Part 15 of

9-1TECHNICALTECHNICALExample of computer signalResolution H× VfH (kHz) fV (Hz) Rating Signal modeDisplaymodeNote 1640 × 35037.9 85.1 VESA VGA-1 Zoom i

9-2TTEECCHHNNIICCAALL((ccoonnttiinnuueedd))Initial set signalsThe following signals are used for the initial settings.The signal timing of some comput

1-3BBEEFFOORREE UUSSEE ((ccoonnttiinnuueedd))ENGLISHPart NamesPower SwitchAC Inlet(to the Power Cord)Ventilation Openings(Intake)ZOOM knobFOCUS ring

1-4BBEEFFOORREE UUSSEE ((ccoonnttiinnuueedd))Part Names (continued)VIDEOSTANDBY/ONPOSITIONFREEZEMAGNIFYVOLUMEAUTOOFFTIMER BLANKMENUSELECTRGBMUTEMENU

1-5INSTALLATIONInstallation of the Projector and ScreenInstall the projector in a suitable environment according to instructions of theaccompanying ma

1-6IINNSSTTAALLLLAATTIIOONN ((ccoonnttiinnuueedd))RGB Signal Input:Connect the RGB IN terminal of the projector to the display signal output of the c

1-7IINNSSTTAALLLLAATTIIOONN ((ccoonnttiinnuueedd))ENGLISHExample of system setupAC InputVideo tape recorder with S jackVideo tape recorderComputer(de

1-8OPERATIONSPower On/OffPower On1. Confirm that power cord is connected properly.2. Push "I" of the power switch. Standby mode is set up an

1-9OOPPEERRAATTIIOONNSS ((ccoonnttiinnuueedd))ENGLISHBasic OperationBasic manipulation to show in the table 1-2 can be done easily by the control pan